Posted in

Are thrust ball bearings suitable for vertical shafts?

If you’ve ever stood next to a large industrial press, watched a rotating satellite dish adjust its angle, or even used a heavy-duty mixer in a commercial kitchen, you’ve likely encountered a vertical shaft application. As a thrust ball bearing supplier who’s talked to hundreds of engineers, plant managers, and small workshop owners over the last 12 years, one question comes up more often than any other: “Are thrust ball bearings even right for a vertical shaft setup?” The short answer isn’t a simple yes or no—though I’ll say this: I’ve seen them work perfectly in the right applications, and I’ve seen them fail catastrophically when misused. Today, I’m breaking down what you need to know before picking a bearing for your vertical shaft, from real-world lessons I’ve learned on the supply floor to the technical details that actually matter. Thrust Ball Bearing

First, let’s start with the basics, because so many people mix up radial and thrust bearings, especially when talking about vertical shafts. A radial bearing is the one you probably know—like the bearings in a car’s wheel, that carry load perpendicular to the shaft’s spin direction. A thrust bearing is built specifically to carry load parallel to the shaft’s axis, the direction that pushes up or down along the shaft’s length. For vertical shafts, that’s exactly the load you’re dealing with: gravity pulling down on the shaft, the weight of whatever’s attached to it, and sometimes even additional axial loads from things like a press applying downward force, or a mixer’s blades pushing against material. Thrust ball bearings are designed to handle that exact force. But here’s the catch: not all thrust ball bearings are the same. There are two main types: single-direction and double-direction. Single-direction thrust ball bearings only handle axial load in one direction, so if your vertical shaft has upward thrust too—like, say, a lift table that pushes up as well as holds weight down—single-direction won’t work. You’ll need double-direction, or a pair of single-direction bearings to counter the upward force.

I learned this the hard way early in my career. Back in 2011, a customer who ran a line of hydraulic lift tables ordered 200 single-direction thrust ball bearings for their vertical lift shafts. They called me three weeks later, panicking, because half the bearings had failed after just a few weeks of operation. When they sent the broken parts back, we saw the issue: not only was the lift carrying downward weight, but the hydraulic cylinders were also pushing upward on the shaft during the raise cycle, and the single-direction bearings couldn’t handle that reverse load. We swapped them for double-direction thrust ball bearings, and those lift tables have been running without a single bearing issue for over a decade. That’s the kind of real-world experience you won’t find in a textbook, and it’s why I always stress to customers that matching the bearing type to their exact load direction is non-negotiable.

Next, let’s talk about limitations, because thrust ball bearings aren’t a one-size-fits-all solution for vertical shafts. The biggest downside is their speed rating. Thrust ball bearings have much lower rotational speed limits than radial ball or roller bearings, and that’s amplified on vertical shafts. Why? Because when a vertical shaft spins, the balls in the thrust bearing have to roll between two raceways, but gravity pulls them downward, creating extra friction and wear at higher speeds. If you’re running a vertical shaft at more than 1,000 RPM, thrust ball bearings are probably not the right call. I’ve had customers come to me wanting to use thrust ball bearings for high-speed vertical conveyors, and I always advise them to look at thrust roller bearings instead—those are built to handle higher speeds and heavier loads for vertical setups, even if they cost a bit more.

Another limitation is misalignment. Vertical shafts, especially long ones in industrial equipment, tend to flex or bend a little under load, or develop small misalignments over time from installation or wear. Thrust ball bearings are much less tolerant of misalignment than other bearing types, like spherical roller thrust bearings. If your vertical shaft has more than a fraction of a degree of misalignment, the balls will start to wear unevenly, the raceways will crack, and you’ll get premature failure. Last year, a mining equipment customer came to me with a vertical shaft for a conveyor hoist that was throwing out thrust bearings every six months. When their maintenance team checked the shaft alignment, they found it was off by 0.8 degrees from the shaft’s centerline. Swapping in spherical roller thrust bearings fixed the issue, because their design lets them compensate for that small misalignment without extra wear. It’s a small detail, but it’s one that trips up so many people.

Now, let’s get into when thrust ball bearings do work best for vertical shafts, because that’s the answer most people are actually looking for. I’ve seen them perform flawlessly in three types of vertical shaft applications: low-speed, light-to-medium load setups; intermittent vertical motion; and applications where space is at a premium. Let’s break each of these down with examples from customers I work with.

First, low-speed, light-to-medium load setups. Think of a vertical rotating display in a retail store, or the shaft that turns a small agricultural seed drill’s vertical agitator, or even the pivot for a large gate on a farm. These applications usually spin at less than 500 RPM, have consistent axial loads from their own weight and the parts attached, and don’t have much misalignment. For these, thrust ball bearings are perfect. They’re compact, they’re affordable, and they do exactly what they’re built to do—carry the axial load without extra friction. Last year, a boutique coffee roaster ordered 12 single-direction thrust ball bearings for their vertical coffee bean hoists. The hoists spin at 120 RPM, hold 500 pounds of beans, and have no reverse load. Those bearings have been running for 18 months with zero maintenance, which is exactly what their budget and timeline called for.

Second, intermittent vertical motion. This is applications where the shaft doesn’t spin nonstop, it moves up and down (or up and down while spinning) for short periods. Like a garage door operator’s vertical shaft, or a medical turntable in a hospital that only moves when a new patient is admitted, or a small crane’s vertical lifting shaft. For these, the speed is almost always very low, and the load is steady during the lift or rotation, then idle the rest of the time. Thrust ball bearings are ideal here because their low cost and simple design make them easy to replace when needed, and their performance is more than enough for the job. I work with a manufacturer of medical imaging equipment who uses double-direction thrust ball bearings for their vertical patient positioning shafts. The shafts move at less than 10 RPM, hold the weight of a person, and only move a few times a day. They’ve been using these bearings for 7 years, and they’ve only had to replace 3 of them across 500 units—way below their maintenance budget.

Third, applications where space is at a premium. Thrust ball bearings are thinner and more compact than most other thrust bearing types, which makes them perfect for tight spaces. If you’re building a piece of equipment where the vertical shaft has almost no room for a thicker bearing assembly, thrust ball bearings are the way to go. For example, a small 3D printer manufacturer I supply uses thrust ball bearings for their vertical Z-axis shaft. The shaft is only 10mm in diameter, and the bearing housing is just 5mm thick. There’s no way a thrust roller bearing would fit there, so the compact size of thrust ball bearings is non-negotiable for their design. They tested a few other bearing types, and none fit or performed as well for their tight space requirements.

Now, let’s talk about installation and maintenance, because even the best bearing will fail if it’s installed wrong, especially on a vertical shaft. From my time on the supply floor, I can say that 70% of bearing failures I see aren’t from the bearing itself—they’re from bad installation or lack of maintenance. For vertical shafts, there are two big installation mistakes to avoid. First, never skip the washer. Thrust ball bearings use two flat washers, one mounted to the shaft and one to the housing. If you skip either, the balls will sit directly against the metal of the shaft or housing, creating extra friction and wear, and leading to early failure. Second, make sure the washers are perfectly aligned, and the shaft is level. If the shaft is even a little tilted, the bearing will wear unevenly. When we ship thrust ball bearings to customers, we always include a one-page guide with installation steps, and I follow up with every new customer for the first month to make sure they’re doing it right. Last quarter, we had a customer who installed their bearings without washers, and within a week they were back with failed units. A quick call walked them through the correct installation, and they’re now a repeat customer who orders bearings every quarter.

Maintenance is equally important. For vertical shafts, the biggest wear factor is lubrication. The balls in the thrust bearing are under constant load, so they need enough lubricant to reduce friction and prevent corrosion. But you don’t want to over-lubricate either—too much grease will build up heat, especially at higher speeds. For low-speed applications, a small amount of lithium-based grease every six months is usually enough. For intermittent applications, a visual check every year works, as long as the bearing isn’t exposed to dust or moisture. Speaking of exposure, if your vertical shaft is in a harsh environment—like a farm, a construction site, or a chemical plant—you’ll need to add a seal to the thrust ball bearing to keep out dirt, water, or chemicals. Standard open thrust ball bearings won’t hold up in these conditions, so we offer sealed variants for exactly that. I once had a customer in a fertilizer plant order open thrust ball bearings for their vertical mixer shafts, and they failed in two weeks because of dust and corrosive fumes. Swapping for sealed bearings extended their bearing life to over a year, which is a huge difference for their maintenance schedule.

Let’s wrap this up with a quick truth: thrust ball bearings are not suitable for every vertical shaft, but they’re an excellent choice for many common applications. If your vertical shaft is running at under 1,000 RPM, has consistent axial load in one or two directions, doesn’t have significant misalignment, and you have space constraints, they’re a cost-effective, reliable choice. If your shaft is running at high speeds, has heavy misalignment, or has extreme loads that exceed their capacity, you’ll want to look at thrust roller bearings or spherical roller thrust bearings instead.

At the end of the day, every application is unique, and there’s no one-size-fits-all answer. If you’re working on a vertical shaft project and you’re not sure if thrust ball bearings are right for you, I’m here to help. I’ve spent the last 12 years learning what works and what doesn’t across hundreds of different industries, and I can help you pick the right bearing for your specific needs, no matter how big or small your project is. Whether you need a single bearing for a hobby project or a bulk order for an industrial line, I’m ready to walk through your requirements, answer your questions, and make sure you get the right product for your application.

References

Insert Ball Bearing Shigley’s Mechanical Engineering Design, 11th Edition, McGraw-Hill, 2020
SKF Thrust Ball Bearing Product Catalog, SKF Group, 2022
American Gear Manufacturers Association (AGMA) Bearing Load and Alignment Guidelines, AGMA, 2021


Yantai Wared Bearing Co., Ltd.
As one of the most professional thrust ball bearing manufacturers and suppliers in China, we also support customized service. Please feel free to wholesale durable thrust ball bearing made in China here and get pricelist from our factory. For price consultation, contact us.
Address: North Street, Donglai Subdistrict, Longkou, Yantai, Shandong Province, China
E-mail: zhang@bearingzwz.com
WebSite: https://www.bearingzwz.com/