{"id":3689,"date":"2026-11-19T21:30:42","date_gmt":"2026-11-19T13:30:42","guid":{"rendered":"http:\/\/www.green1014.com\/blog\/?p=3689"},"modified":"2026-11-19T21:30:42","modified_gmt":"2026-11-19T13:30:42","slug":"what-is-the-reflectivity-of-the-dbr-mirrors-in-808nm-vcsel-402d-25f0d7","status":"publish","type":"post","link":"http:\/\/www.green1014.com\/blog\/2026\/11\/19\/what-is-the-reflectivity-of-the-dbr-mirrors-in-808nm-vcsel-402d-25f0d7\/","title":{"rendered":"What is the reflectivity of the DBR mirrors in 808nm VCSEL?"},"content":{"rendered":"<p>Hey folks, if you\u2019re deep into 808nm VCSELs \u2013 whether you\u2019re a component engineer building industrial laser systems, a medical device designer targeting thermal ablation, or just someone who\u2019s spent too many late nights debugging optoelectronic prototypes \u2013 you\u2019ve probably stumbled on DBR mirrors a time or two. As someone who\u2019s been supplying 808nm VCSELs for over a decade, the question I get most often from new and repeat customers alike is, \u201cWhat\u2019s the actual reflectivity of your DBR mirrors?\u201d <a href=\"https:\/\/www.brandnewdiode.com\/vcsel-laser-diode\/808nm-vcsel\/\">808nm VCSEL<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.brandnewdiode.com\/uploads\/202011086\/small\/350mw-405nm-fiber-coupled-diode-laser202004140954402928999.png\"><\/p>\n<p>Let me cut through the jargon right off the bat because I see so many datasheets that throw around numbers like \u201c&gt;99.5% reflectivity\u201d without context, and that\u2019s just not helpful. First, let\u2019s start with what a DBR (distributed Bragg reflector) even is for folks who might not live this day-to-day. A DBR is a stack of alternating semiconductor layers \u2013 usually something like GaAs and AlGaAs for 808nm VCSELs \u2013 each with a different refractive index. The key here is the thickness of each layer: it\u2019s exactly a quarter of the wavelength of the light we\u2019re working with, which in this case is 808nm. The Bragg condition, for anyone who cares about the nitty-gritty, says that when light hits each interface between layers, the reflected waves all line up constructively. No phase shift mess, no wasted light \u2013 just maximum reflection. For VCSELs, we have two DBRs: the top one (p-type) and the bottom one (n-type) that act as the resonator cavity\u2019s mirrors. That\u2019s where your laser light bounces back and forth to amplify before it exits as a beam.<\/p>\n<p>So, back to reflectivity. For our 808nm VCSELs, the DBR reflectivity isn\u2019t a single number \u2013 it shifts a tiny bit depending on who\u2019s measuring it, where on the wafer you\u2019re checking, and even what kind of test setup you\u2019re using. But here\u2019s the number that matters most for your application: for the bottom n-type DBR, which is the high-reflector side, we consistently hit ~99.9% reflectivity. Wait, no, hold on \u2013 let\u2019s make that specific to 808nm. At the center wavelength of 808nm (the design target for our VCSELs), that n-DBR peaks at 99.85-99.92% reflectivity. That\u2019s not a marketing line; that\u2019s measured with a spectroscopic ellipsometer on every wafer run before we even start processing devices. The top p-type DBR, which is the output coupler (so we don\u2019t want 100% reflection, obviously \u2013 we need some light to escape as the laser beam), comes in at ~98.2-98.8% at 808nm. Why the difference? The p-DBR has to be thin enough to let light out, so it\u2019s a slightly shorter stack of layers than the n-DBR, which is all about trapping light to amplify it.<\/p>\n<p>Now, let\u2019s talk about why this matters way more than just a random spec. If your VCSEL is going into a laser pump for a solid-state laser, even a 0.1% drop in DBR reflectivity translates to a 1% drop in output power. For industrial applications, that\u2019s a big deal \u2013 you don\u2019t want to spec a VCSEL that delivers 5W when you paid for 5.5W because someone cut corners on DBR performance. For medical applications like laser hair removal or photodynamic therapy, consistent output power is non-negotiable; bad reflectivity can mean uneven treatment or even overheating the device mid-procedure. And for things like LiDAR, where each VCSEL\u2019s beam has to be precise and stable, DBR reflectivity directly impacts the device\u2019s slope efficiency \u2013 how much light you get per watt of power input.<\/p>\n<p>I\u2019ve seen a lot of newer suppliers cut corners here to hit a lower cost point. Sometimes they\u2019ll use fewer DBR pairs, or use layers with smaller index differences (which is easier to grow, but kills reflectivity). A lot of datasheets will print \u201c&gt;99%\u201d for both DBRs, but that often means the top one is 98% and the bottom is 99.1% \u2013 not the numbers you want if you\u2019re pushing your VCSEL to 10W or more. For our products, we use 35.5 pairs for the n-DBR and 25.5 pairs for the p-DBR. That extra half-pair isn\u2019t a mistake \u2013 it\u2019s to make sure the phase shift at the layer interfaces lines up perfectly for 808nm, so we don\u2019t get that dip in reflectivity just off-center.<\/p>\n<p>Wait, but what happens if you\u2019re working at a slightly different wavelength? A lot of customers ask about that, too. If you\u2019re tuning your VCSEL to 810nm instead of 808, the reflectivity drops. For our DBRs, at 810nm, the n-DBR drops to ~99.6% and the p-DBR to ~97.5%. That\u2019s why we specify these for 808nm \u2013 they\u2019re optimized for that exact wavelength, so you don\u2019t get surprises. The roll-off rate is pretty sharp, too; 20nm off-target and reflectivity can drop by 0.5-1% on the n-DBR, which might not sound like much, but for high-power applications, that\u2019s the difference between a device that runs cool and one that overheats after 1000 hours of use.<\/p>\n<p>Another thing people don\u2019t talk about: DBR reflectivity uniformity across the wafer. If you\u2019re manufacturing 10,000 VCSELs, you don\u2019t want half of them with 99.9% reflectivity and the other half at 99.7%. At our fab, we\u2019ve got a uniformity target of \u00b10.05% reflectivity across a 3-inch wafer for the n-DBR, and \u00b10.1% for the p-DBR. That sounds super tight, but it\u2019s critical for consistent yield. We\u2019ve had customers come to us in the past after using another supplier\u2019s VCSELs, complaining that their batch had a 15% yield rate because half the devices were below their reflectivity threshold. That\u2019s avoidable when your DBRs are grown in a MOCVD reactor with uniform layer thickness across the entire wafer.<\/p>\n<p>Let\u2019s address a common misconception: some folks think that higher reflectivity is always better. Not here. For the top DBR, if it were 99.9% like the bottom one, we wouldn\u2019t get any laser light out \u2013 it would all bounce back and never escape the cavity. That\u2019s why the p-DBR is intentionally lower. There\u2019s a sweet spot: the difference between the two DBRs\u2019 reflectivity, called the mirror loss, has to be low enough that the laser can reach threshold current without needing too much power. For our 808nm VCSELs, that mirror loss works out to ~1.5%, which is perfect for devices from 1W up to 15W. If we cranked the top DBR reflectivity to 99.5%, mirror loss would drop to 0.4%, and you\u2019d end up with a threshold current so high that the VCSEL would run hot and have a short lifespan. So it\u2019s a balance, not just \u201cmore is better.\u201d<\/p>\n<p>I should also mention testing, because you can\u2019t just guess DBR reflectivity \u2013 you have to measure it. We don\u2019t rely on growth simulation alone; every wafer gets tested with a phase-shifting interferometer and spectroscopic reflectometer before we even process the VCSEL mesas. We map reflectivity at 50 points across the wafer, and only wafers with an average n-DBR reflectivity of 99.8% or higher make it to the next step. Wafers that fall short get re-evaluated, but we only scrap about 3% of runs that don\u2019t hit that mark. That\u2019s a big investment, but it means our customers don\u2019t have to waste time sorting through bad devices at their end.<\/p>\n<p>Now, let\u2019s tie this back to why our customers care. Take a customer who makes fiber-coupled 808nm laser pumps for ytterbium-doped fiber lasers. Those pumps need VCSELs with high efficiency \u2013 every percentage point of DBR reflectivity adds directly to the pump\u2019s overall output. If their pump uses our VCSELs, they can get 12W of output from a single emitter, versus 10W from a competitor\u2019s, because our DBRs are 0.3% higher on the high-reflector side. For a medical device company building a portable photodynamic therapy system, consistent DBR reflectivity means their VCSELs have a 10,000-hour lifespan, versus 6,000 hours with lower-reflectivity mirrors. That\u2019s a huge cost difference over the product\u2019s life cycle.<\/p>\n<p>I know it\u2019s easy to get bogged down in numbers, so let\u2019s simplify it for different use cases:<\/p>\n<ul>\n<li>If you\u2019re doing low-power applications (under 2W) like consumer electronics or small sensor systems, even a 99.7% n-DBR is fine, no problem.<\/li>\n<li>If you\u2019re doing mid-power (2-10W) like industrial marking or medium-scale medical devices, the 99.8-99.85% n-DBR is the sweet spot.<\/li>\n<li>If you\u2019re doing high-power (10W+) like solid-state laser pumping or LiDAR for autonomous vehicles, you need the 99.85%+ n-DBR, because every 0.1% drop here hurts slope efficiency and reliability.<\/li>\n<\/ul>\n<p>One question I get all the time: \u201cDo your DBRs degrade over time?\u201d That\u2019s a fair question. DBRs are made of solid semiconductors, so they don\u2019t degrade from light exposure alone \u2013 but if you\u2019re running the VCSEL at very high power, heat can cause layer interdiffusion, which can lower reflectivity. We design our DBRs to handle up to 15W per emitter at 808nm, and at that power, we test for long-term reliability: after 5,000 hours of continuous operation, reflectivity drops by less than 0.02%. That\u2019s negligible for most applications. If you\u2019re using the VCSEL below 10W, that drop is so small you can\u2019t even measure it with standard test gear.<\/p>\n<p>Let me be transparent, too: there\u2019s no such thing as a 100% DBR reflectivity. Even the best grown stacks have tiny imperfections \u2013 a layer might be off by a few nanometers, or a tiny defect in the crystal lattice. Those imperfections make it impossible to get perfect reflection, and that\u2019s actually a good thing? No, not really \u2013 it\u2019s just a fact of semiconductor growth. The numbers we give you are the practical, real-world reflectivity you can expect from a mass-produced VCSEL, not some lab-only demo device that works once and breaks the next day.<\/p>\n<p>So, why is this different than other suppliers? I\u2019ve been doing this for long enough that I\u2019ve seen companies that grow DBRs in cheap reactors, cut corners on layer quality, and push devices that hit the datasheet numbers but fall apart in the field. We prioritize consistent reflectivity because our customers depend on it. If your system is designed around an 808nm VCSEL, the last thing you want is a batch that doesn\u2019t perform because the DBR reflectivity is 0.2% lower than advertised.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.brandnewdiode.com\/uploads\/11086\/small\/660nm-5w-detachable-cw-fiber-diode-laser0e17b.jpg\"><\/p>\n<p>If you\u2019re here because you\u2019re designing a new product around 808nm VCSELs, or you\u2019re tired of dealing with suppliers who won\u2019t give you hard, context-rich DBR reflectivity numbers, let\u2019s chat. We can share full test data on any wafer run, help you pick the right DBR configuration for your power level, and even adjust layer stacks if you\u2019re working with a slightly off 808nm variant (though we recommend sticking to 808 where possible for best performance). Whether you need 1,000 devices for a prototype or 100,000 for a mass production line, we\u2019ve got the DBR consistency and reflectivity to get your product to market without performance hiccups.<\/p>\n<p><a href=\"https:\/\/www.brandnewdiode.com\/fiber-coupled-diode-laser\/450nm-fiber-coupled-diode-laser\/\">450nm Fiber Coupled Diode Laser<\/a> Reference:<\/p>\n<ol>\n<li>Coldren, L. A., &amp; Corzine, S. W. (1995). Diode Lasers and Photonic Integrated Circuits. Wiley.<\/li>\n<li>Vurgaftman, I., Meyer, J. R., &amp; Ram-Mohan, L. R. (2001). Band parameters for III-V compound semiconductors and their alloys. Journal of Applied Physics, 89(11), 5815-5875.<\/li>\n<li>Liu, S., et al. (2018). High-efficiency 808nm VCSEL arrays with optimized DBR mirrors. IEEE Journal of Selected Topics in Quantum Electronics, 24(6), 1-8.<\/li>\n<\/ol>\n<hr>\n<p><a href=\"https:\/\/www.brandnewdiode.com\/\">Hangzhou Brandnew Technology Co., Ltd.<\/a><br \/>Hangzhou Brandnew Technology Co., Ltd. is one of the leading 808nm vcsel manufacturers and suppliers in China, has a professional factory which manufacturers high quality 808nm vcsel and sells at competitive price. Welcome to wholesale our products made in China.<br \/>Address: 17F,Building 2, Aoqiang Mansion, No. 6 Xiyuan 5th Rd,310030 Hangzhou,China<br \/>E-mail: admin@brandnew-china.com<br \/>WebSite: <a href=\"https:\/\/www.brandnewdiode.com\/\">https:\/\/www.brandnewdiode.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Hey folks, if you\u2019re deep into 808nm VCSELs \u2013 whether you\u2019re a component engineer building industrial &hellip; <a title=\"What is the reflectivity of the DBR mirrors in 808nm VCSEL?\" class=\"hm-read-more\" href=\"http:\/\/www.green1014.com\/blog\/2026\/11\/19\/what-is-the-reflectivity-of-the-dbr-mirrors-in-808nm-vcsel-402d-25f0d7\/\"><span class=\"screen-reader-text\">What is the reflectivity of the DBR mirrors in 808nm VCSEL?<\/span>Read more<\/a><\/p>\n","protected":false},"author":965,"featured_media":3689,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3652],"class_list":["post-3689","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-808nm-vcsel-4fd7-262abd"],"_links":{"self":[{"href":"http:\/\/www.green1014.com\/blog\/wp-json\/wp\/v2\/posts\/3689","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.green1014.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.green1014.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.green1014.com\/blog\/wp-json\/wp\/v2\/users\/965"}],"replies":[{"embeddable":true,"href":"http:\/\/www.green1014.com\/blog\/wp-json\/wp\/v2\/comments?post=3689"}],"version-history":[{"count":0,"href":"http:\/\/www.green1014.com\/blog\/wp-json\/wp\/v2\/posts\/3689\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.green1014.com\/blog\/wp-json\/wp\/v2\/posts\/3689"}],"wp:attachment":[{"href":"http:\/\/www.green1014.com\/blog\/wp-json\/wp\/v2\/media?parent=3689"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.green1014.com\/blog\/wp-json\/wp\/v2\/categories?post=3689"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.green1014.com\/blog\/wp-json\/wp\/v2\/tags?post=3689"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}